DIY Peg Coat Rack

The twins turn one next month. Gone are the babes swaddled safely in my arms, here are independant little explorers roaming free and keeping me on my toes!

Baby proofing has gone beyond safety gates, as we realize a safe home is a relaxed home. At this stage everything is going in their mouths so it’s essential things are out of reach, but still totally accessible to Brock and me.

This past weekend, Brock whipped up this new peg coat rack. Not only does it look totes adorbs (he he) but it holds much more than coats. We’ve been hanging everything in sight, from shoes to recycling to mail and keys. It’s so handy and looks great! We’re wondering why we didn’t think of doing it before, and it only cost about $11 to make!

boxwood clippings_diy peg coat rack

I had every intention to shoot the process, but my hands were full with the ladies, so I’ll just have to explain it!

You Will Need:

1 plank of wood, 3.5″ width (primed, cut to desired length)

1 or 2 dowels, 1″ diameter (number of dowels depends on desired length)

Saw

Drill and 1″ drill bit (same size as dowels)

Wood glue

Sand paper

Paint

Wood screws (for mounting to the wall)

.

How To:

Measure out your space and decide the length of the peg rack and the distance you want between each peg. The Shakers did their pegs 6″ apart, so we went with their school of thought, along an 8-foot rack (16 pegs). Measure out the distance between each peg along the wood plank, making sure to measure from the middle of the plank (so you don’t end up with a peg only one inch from one end and 6 inches from the other end).

Mark the center point where each peg should go, making sure to keep all pegs along the centerline of the plank. Brock made a template out of an old scrap of wood the same width as the plank to make sure the distance between pegs and distance from the edge was uniform.

Next, drill 1″ holes for each peg, making sure not to angle the drill (if you know someone with a drill press, this would be the best way to do it; otherwise, just use a steady hand). Brock drilled all the way through each hole, but if you’re using a drill press, it would be best to drill only 3/4 the distance through the plank to allow more surface area for the wood glue to bond. Whichever way you do it, it needs to be uniform to make sure the peg lengths are the same across the plank.

Cut the dowels to your desired peg lengths (ours were 5″). Dry-fit the pegs in the holes to make sure they fit snuggly. If they are loose, don’t worry; you can use a household caulk to fill in the extra space prior to painting. Glue one end of each peg into place using a very strong wood glue and leave for 24 hours to fully cure.

Sand any sharp or splintered edges as needed, making sure to remove any excess glue, then paint (and caulk if needed). Once the paint has dried, you are ready to mount your new peg coat rack! To do this, use a stud-finder to find the studs behind the wall, then simply drill small holes into the plank for your screws. Use a level to make sure your new rack is positioned correctly, and then screw it to the wall. Lastly, use some caulk to hide the screws, and the re-paint over the screw holes, and you’re done!

boxwood clippings_diy peg coat rack

 Ours is placed between our garage door and kitchen. Even in narrow hallways it works great and helps maximize the space.

boxwood clippings_diy peg coat rack

 Here’s how the hallway looked before. Functional and tidy, but not baby friendly.

boxwood clippings

Has January been an organizing month for you, too? We love a fresh space for a fresh year!

3 Responses to “DIY Peg Coat Rack”

  1. John Says:

    Brilliant – no point in doing a short run, you may as well fill the wall.

  2. Kimberly Clayton Says:

    Good idea hanging the bucket for small items. I might just do this peg board for my side door. Thanks

  3. Boxwood Clippings » Blog Archive » Organization: Sarah’s Pantry Overhaul! Says:

    […] we removed ours in the hallway for the peg rail (see HERE) I’ve been desperate for a place for invitations and […]